Color Works-White

Kuvaus

spraymaali

Väri: Valkoinen

 

Excellently suitable for all DIY and handicraft works on wood, metal, aluminium, glass, stone, carton, paper, eternite, china and many paintable plastics. For indoor and outdoor applications.

Quality and properties

High-grade synthetic quality

Quick-drying

Suitable to paint and repair indoor and outdoor objects

Good coverage and filling power

Good colour and gloss retention

Weather resistant, light-proof, UV-resistant

Excellent flow for even surfaces

Good adherence on nearly all materials

Scratch-, bump and shock-proof

Temporarily resistant against fuel, chemicals and weather influences

Physical and chemical data

Basis of the binder: Alkyd resin

Colour: specific

Smell: solvent

Degree of gloss (at measurement angle 60° acc. to DIN 67530):

glossy: 85-90 gloss units

satin matt: 30-35 gloss units

Efficiency:

Depending on consistence and color of the ground:

400 ml are sufficient for approx. 0.8 – 1.2 m²

depending on colour

Drying time (at 20°C, 50% relative air humidity):

Dust-dry: after approx. 30 minutes

Non-sticky: after approx. 4 hours

Cured: after approx. 24 hours

Coatable: within 2 hours or after approx. 24 hours

The drying time depends on surrounding temperature, air humidity and thickness of the applied coat.

Temperature-resistant: up to 80°C

Storage stability:

Aerosols: 10 years, if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%)

Size: aerosol cans, maximum nominal volume 400 ml

Environment and labelling

Environmentally compatible: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

 

Disposal: Please mind the residue inside the containers. Completely emptied containers can be used for recycling. If cans are not emptied, they should be disposed off as “special refuse”.

Only for DE: In order to ensure a high reuse and recycling rate, the legislator requires, in accordance with §15 – VerpackG, Paragraph 1, the return of transport, sales or outer packaging, alternatively, however, deviating agreements can also be made.

 

Labelling: All products of European Aerosols comply with the current status of their labelling regulations. Classification and distinction takes place by the presently legal form of the Globally Harmonized System of Classification and Labelling of Chemicals (GHS) or rather by CLP 1272/2008/EG regulations. Our safety data sheets comply with the current form of REACH 1907/2006/EG, article 31 und appendix II,

 

Instruction manuel

The most MoTip spray paints have a so-called no-spray ring or a tamper-proof cap. This is to avoid unauthorized use. Please see the corresponding advises on the cap or on the label.

Before use, carefully read and observe the warning texts on the label!

 

Preparation of the ground:

 

The ground has to be clean, dry and free from fat.

Remove residues of old paintings and rust, then sand and prime.

Plastic Parts have to be primed with MoTip Plastic Primer.

Let dry for 1 – 2 hours.

 

 

Lacquering:

 

The ground has to be clean, dry and free from fat.

Bring the can to room temperature.

Processing temperature during 15 – 25°C.

Mask off the areas which are not to be painted.

Before use, shake the can for 2 minutes.

Test compatibility of the spray at an invisible spot.

Spray from a distance of approx. 25 cm.

Spray several thin coats in 2 minute intervals.

Shake the can during use from time to time.

After use, turn the can upside down and spray to clean the valve.

Do not overpaint with acrylic or nitro combi paints – not even after curing!

Tips for spray painting

Protect the object and the surrounding area from spray mist. When painting small areas it is recommended that a piece of card is used as a mask, with a hole cut in it slightly larger than the area to be sprayed. The mask should be held 1 to 2 cm from the surface. With this method, the mainly part of the spray mist is brought under control. It recommends to mask parts not to be lacquered, to protect the surrounding against the spray mist.

 

The aerosol can should have room temperature.

 

Temperature should range between +10°C and +25°C, max. air humidity 60 %.

 

Store in a dry place. Protect from direct sunlight and other sources of heat. Use only during dry weather, in places protected from the wind, and in well-ventilated rooms. Follow the warning texts on the labels!